우리 의 제품
마르는 16Mn 편흡입 많은 양 산업적 원심분리기 팬들 소재
16Mn Single Suction High Volume Industrial Centrifugal Fans Materials Drying Introduction The 4-14 series centrifugal fan is suitable for indoor ventilation in general factories and large buildings. It can be used to input gas as well as to output gas. Made of high quality carbon steel, Stainless steel or other metal materials can also be used according to user requirements. Detail introduction The impeller is annealed to completely eliminate structural stresses generated
장수 산업적 원심분리기 팬들 고로를 운전하는 탄소강 v 벨트
Carbon Steel V-Belt Driving Long Life Industrial Centrifugal Fans Furnace Introduction The 4-14 series centrifugal fan is suitable for indoor ventilation in general factories and large buildings. The fan speed can be flexibly set by matching different pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. The bearing housing uses a labyrinth mechanical seal, a unique Leak proof oil design inside, a vent hole at the top, and a sealant on
합금 강 단일의 유입구 긴 수명 원심력 환풍기들 에어 서플라이
Alloy Steel Single Inlet Long Lifetime Centrifugal Ventilation Fans Air Supply Introduction The 4-10 series centrifugal Fan can be used for indoor ventilation in general factories and large buildings. No viscous substances are allowed in the gas, and the dust and hard particles contained in the gas are not more than 150 mg/m3. The gas temperature does not exceed 80°C, and similar gas properties are also available. Detail introduction Mainly to meet the dust emission
HG785는 마르는 철강 아주 튼튼한 원심력 환풍기들 소재를 합금했습니다
HG785 Alloyed Steel Heavy Duty Centrifugal Ventilation Fans Materials Drying Introduction The 4-10 series centrifugal Fan can be used for indoor ventilation in general factories and large buildings. The casing is welded into a cochlear body by steel plates.The casing is welded into a cochlear body by steel plates. Detail introduction The transmission group is composed of a main shaft, a belt wheel and a water-cooled bearing box. The housing is welded into a cochlear body with
저압이 포워드 야금학 원심력 환풍기들 방식
Low Pressure Forward Metallurgy Centrifugal Ventilation Fans Anticorrosion Introduction The 4-10 series centrifugal Fan can be used for indoor ventilation in general factories and large buildings. The converging and streamlined air inlet is made into a unitary structure and bolted to the inlet side of the fan. A device for regulating the flow of the fan, axially mounted in front of the air inlet. The adjustment range is from 0° (full open) to 90°(fully closed). Detail
뒤로 스테인레스 강 중간 압력 주조공장 원심력 환풍기들
Stainless Steel Medium Pressure Foundry Centrifugal Ventilation Fans Backward Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It has a larger output flow than the 5-11 series. It is also used to transport a variety of common gases and hard materials in the industrial field, the application object is exactly the same as 5-11 series fan. Detail introduction This can use different speeds to meet the
알루미늄 합금 에너지 효율 원심력 환풍기들은 공장을 숯으로 만듭니다
Aluminium Alloyed Energy Efficiency Centrifugal Ventilation Fans Coal Mill Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It has a larger output flow than the 5-11 series. It is also used to transport a variety of common gases and hard materials in the industrial field, the application object is exactly the same as 5-11 series fan. Detail introduction The casing is welded into a cochlear body with alloy
아주 튼튼하 반대 폭발 석회 소성로 보일러 팬 고온
Heavy Duty Anti-Explosion Lime Kiln Boiler Fan High Temperature Introduction This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above situation, considering the practicability of the fan, in addition to the 20-ton boiler ID fan need large power coupling direct transmission, the other uses the triangular belt type transmission. Detail introduction
산업적 장수 용광로 보일러 팬 폭발 가공
Industrial Long Life Blast Furnace Boiler Fan Explosion Proofing Introduction This type of fan is currently used in the boiler industry. The air volume of the induced draft fan and the difference in wind pressure are relatively large, in order to adapt to the above situation, considering the practicability of the fan, in addition to the 20-ton boiler ID fan need large power coupling direct transmission, the other uses the triangular belt type transmission. Detail introduction
뒤처지는 구부러진 중간 압력 폭파 방지 보일러 팬
Backward Curved Medium Pressure Explosion Protection Boiler Fan Introduction This series fans not only provide high efficiency and energy saving equipment for cement industry, but also the better equipment for other industrial furnaces. The product has advanced design, compact structure, easy to remove the maintenance, safe and reliable operation, wear resistance, high temperature resistant, high efficiency, low noise, smooth performance curve, wider range of flow control,
화로를 하소하는 Q235 고압 뒤처지는 구부러진 보일러 팬
Q235 High Pressure Backward Curved Boiler Fan Calcining Kilns Introduction This series of fan is suitable for conveying non-corrosive, non-spontaneous combustion, temperature does not exceed 700℃ high temperature gas, dust and hard particles contained in the medium is not more than 150mg/m3. Detail introduction There are 12 forward bending blades on the impeller. After the impeller is formed, the dynamic and static balance and overspeed test are carried out to ensure the
탄소강 높은 마모 방지 발전소 팬 많은 양
Carbon Steel High Wear Resistance Power Plant Fan High Volume Introduction This fan is designed for the purpose of using industrial boiler to work in the high-efficiency area and achieve the energy-saving target. Before the induced draft fan, dust removal device with a dust removal efficiency of no less than 85% must be installed to reduce the dust content of the smoke entering the fan. Detail introduction The fan system running at normal temperature with an impeller diameter
Q235 단일의 유입구 시멘트 선풍기 많은 양 뒤처지는 에너지 절약
Q235 Single Inlet Cement Fan High Volume Backward Energy Saving Introduction The gas delivered by the 4-14 series fan should be no more than 80 °C air and other gases that are not self-igniting and are not harmful to the human body and are not corrosive to steel materials. No viscous substances are allowed in the gas, and the dust and hard particles contained in the gas are not more than 150 mg/m3. Detail introduction It can also be made into explosion-proof and flame
16Mn v 벨트 드리븐 시멘트 팬 마멸 저항 건축물 통풍
16Mn V-Belt Driven Cement Fan Abrasion Resistant Building Ventilation Introduction G4-10 and Y4-10 series ventilation and induced draft fans are suitable for the ventilation and induced draft fan systems of 2~670T/h steam boilers in thermal power plants. It can work stably at a high medium temperature, and can output a large gas flow with low noise when the pressure requirement is met. The impeller is annealed to eliminate the internal stress generated during welding,
반대 연마재를 구하는 중간 압력 발전소 선풍기 효율적 에너지
Medium Pressure Power Plant Fan Efficient Energy-Saving Anti Abrasive Introduction The fan speed can be flexibly set by matching different belt pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. The impeller is subjected to a high standard of dynamic balancing adjusting to ensure stable operation of the fan. It has the characteristics of not easy dust accumulation and wear resistant, high efficiency and low noise. This series is a
송풍기 반대 폭발을 취급하는 16Mn 고온 재료
16Mn High Temperature Material Handling Blower Anti-Explosion Introduction 6-12 series high-pressure heavy-duty centrifugal fan, suitable for conveying non-flammable gas and granule/powder/chip/fiber material at normal temperature or high temperature. Bearing cooling method: according to gas temperature and operating environment conditions choose low-cost water-cooling method or oil-cooling method with good heat dissipation performance. For extremely high temperature
송풍기 에너지 효율을 취급하는 Q345 고압 물질
Q345 High Pressure Material Handling Blower Energy Efficiency Introduction The 9-11 series fan has a large flow rate and moderate pressure. This fan is designed for the purpose of using industrial boiler to work in the high-efficiency area and achieve the energy-saving target. It has been compared with similar foreign products and tested by model test. Detail introduction 1. The fan can output very high pressure, suitable for any need to transport high pressure & normal
송풍기 방폭을 취급하는 단일의 유입구 포워드 자료
Single Inlet Forward Material Handling Blower Explosionproof Introduction The 9-08 series fan has a large flow rate and moderate pressure. It’s suitable for conveying normal temperature or high temperature non-flammable gas (normal air, high temperature gas, corrosive gas, dusty gas), and conveying granule/powder/chip/fiber material. Detail introduction 1. The fan can output very high pressure, suitable for any need to transport high pressure & normal temperature gas
